Search Results

For in vitro diagnostic use only. VITROS® Chemistry Products HCY 2 Reagent is used on VITROS® Systems to quantitatively measure total homocysteine concentration in human serum and plasma. Serum and plasma homocysteine levels can assist in the diagnosis and treatment of patients suspected of having hyperhomocysteinemia and homocystinuria. For in vitro diagnostic use only. VITROS® Chemistry Products HCY 2 Performance Verifiers are assayed controls used to monitor performance of VITROS® Chemistry Products HCY and VITROS® Chemistry Products HCY 2 Reagents on VITROS® Systems.

The VITROS® Chemistry Products HCY 2 Reagent is used in conjunction with the VITROS® Chemistry Products Calibrator Kit 27 and VITROS® Chemistry Products FS Diluent Pack 2 (BSA/Saline) on VITROS® 5.1 FS Chemistry Systems, VITROS® 4600 Chemistry Systems, and the VITROS® 5600 Integrated Systems to quantitatively measure total homocysteine concentration in human serum and plasma. The VITROS® Chemistry Products HCY 2 Reagent consists of one dual chambered reagent pack containing two ready-to-use liquid reagents, one in each chamber. Disulfide linked homocysteine (oxidized forms) in the sample is reduced by Tris (2-Carboxyethyl) Phosphine hydrochloride (TCEP) to form reduced homocysteine. Reduced homocysteine reacts with serine in the presence of cystathionine ß-synthase (CBS) to form Lcystathionine. L-cystathionine is broken down by cystathionine ß-lyase (CBL) to produce homocysteine, pyruvate and ammonia. Pyruvate is reduced to lactate by lactate dehydrogenase (LDH) using NADH as coenzyme. The concentration of homocysteine is directly proportional to the amount of NADH converted to NAD and is measured spectrophotometrically at 340 nm. The VITROS® Chemistry Products Calibrator Kit 27 is prepared from an aqueous solution containing amino acids and inorganic acid. These standards are used to calibrate the VITROS® 5.1 FS Chemistry Systems, VITROS® 4600 Chemistry Systems, and VITROS® 5600 Integrated Systems for the quantitative measurement of homocysteine. The VITROS® Chemistry Products HCY 2 Performance Verifiers I, II and III are prepared from processed human serum to which amino acid and preservative have been added. These are assayed controls used to monitor performance of VITROS® Chemistry Products HCY and VITROS® Chemistry Products HCY 2 Reagents on VITROS® Systems. The VITROS® Chemistry Products FS Diluent Pack 2 (Saline/BSA) is a common reagent that is used by multiple assays on VITROS® Systems. This is a dual chambered package containing two ready-to-use liquid diluents. Diluent 1 is prepared from processed water to which inorganic salt has been added. Diluent 2 is prepared from processed water to which bovine serum albumin, inorganic salts and preservatives have been added.

Diazyme's HCY POC Test Kit is intended to be used with the SMART analyzer in a Point-of-Care setting for the in vitro quantitative determination of total L-homocysteine in serum or plasma. The assay can assist in the diagnosis and treatment of patients suspected of having hyperhomocysteinemia and homocystinuria. For in vitro diagnostic use only.

Diazyme HCY POC Test Kit contains reagents intended for use with the SMART analyzer for the quantitative determination of Homocysteine (HCY) in human serum or plasma. Diazyme HCY POC Test is based on a novel enzyme cycling method as published in the Journal of Clinical Chemistry. In this assay, oxidized HCY is first reduced to free HCY which then reacts with a co-substrate, S-adenosylmethionine (SAM) catalyzed by a HCY S-methyltransferase to form methionine (Met) and S-adenosylhomocysteine (SAH). SAH is assessed by coupled enzyme reactions including SAH hydrolase, adenosine (Ado) deaminase and glutamate dehydrogenase, wherein SAH is hydrolyzed into adenosine (Ado) and HCY by SAH hydrolase. The formed HCY that is originated from the co-substrate SAM is cycled into the HCY conversion reaction by HCY S-methyltransferase. This forms a co-substrate conversion product-based enzyme cycling reaction system with signification of detection signals. The formed Ado is immediately hydrolyzed into inosine and ammonia which reacts with glutamate dehydrogenase with concomitant conversion of NADH to NAD+. The concentration of HCY in the sample is indirectly proportional to the amount of NADH converted to NAD+ (ΔA340mm). The Diazyme HCY POC Test system thus consists of the following: - HCY POC Test Kit. Reagents are provided in prefilled tubes, cuvettes and . cuvette caps. The DRS cuvette and cuvette caps can only work with the SMART analyzer. - HCY POC Test Control Kit. Controls are provided for quality control of the . HCY POC Test.

Reagents: ST AIA-PACK Homocysteine is designed for IN VITRO DIAGNOSTIC USE ONLY for the quantitative measurement of homocysteine in human serum, heparinized plasma or EDTA plasma using a Tosoh AlA System Analyzer. Homocysteine measurements are used in the diagnosis and treatment of hyperhomocysteinemia or homocystinuria. Calibrators: ST AIA-PACK Homocysteine Calibrator Set is intended for IN VITRO DIAGNOSTIC USE ONLY for the callbration of the ST AIA PACK Homocysteine assay using a Tosoh AIA System Analyzer. Controls: The AIA-PACK Homocysteine Control Set is intended for IN VITRO DIAGNOSTIC USE ONLY for performing quality control procedures with the ST AIA-PACK Homocysteine Assay.

The ST AIA-PACK Homocysteine is a competitive enzyme immunoassay which, after sample pretreatment, is performed entirely in the ST AIA-PACK Homocysteine test cups. Oxidized homocysteine is reduced by tris (2-carboxyethyl) phosphine (TCEP) to the free form and converted to S-adenosyl-L-homocysteine (SAH) by the SAH hydrolase and excess adenosine prior to the immunoassay. SAH present in the pretreated sample competes with immobilized SAH on magnetic beads for binding sites of the enzyme-labeled anti-SAH mouse monoclonal antibody. The magnetic beads are washed to remove unbound anti-SAH mouse monoclonal antibody and are then incubated with a fluorogenic substrate, 4-methylumbelliferyl phosphate (4MUP). The rate of fluorescence produced by the enzyme reaction indicates the amount of enzyme-labeled anti-SAH mouse monoclonal antibody. The amount of antibody that binds to the beads is inversely proportional to the homocysteine concentration in the test sample. A standard curve is constructed, and unknown sample concentrations are calculated using this curve.

The Homocysteine Enzymatic Assay is an in vitro test for the quantitative determination of total L-homocysteine in human serum and plasma on Roche/Hitachi cobas c systems. The assay can assist in the diagnosis of patients suspected of having hyperhomocysteinemia or homocystinuria. The Homocysteine Calibrator Kit is intended for use in the calibration of quantitative Roche methods on Roche clinical chemistry analyzers as specified in the value sheets. The Homocysteine Control Kit is intended for use in quality control by monitoring accuracy and precision for the quantitative methods as specified in the value sheets.

Assay: The Homocysteine Enzymatic Assay is based on an enzyme cycling assay principle that assesses the co-substrate conversion product. In this assay, oxidized homocysteine (Hcy) is first reduced to free Hcy which then reacts with a co-substrate, S-adenosylmethionine, to form methionine and S-adenosylhomocysteine (SAH), catalyzed by a Hcy S-methyltransferase. SAH is assessed by coupled enzyme reactions where SAH is hydrolyzed into adenosine (Ado) and Hcy by SAH hydrolase, and Hcy is cycled into the Hcy conversion reaction to form a reaction cycle that amplifies the detection signal. The formed Ado is immediately hydrolyzed into inosine and ammonia which reacts with glutamate dehydrogenase with concomitant conversions of NADH to NAD*. The concentration of Hcy in the sample is indirectly proportional to the amount of NADH converted to NAD which is measured spectrophotometrically at 340 nm. Calibrator: The Homocysteine Calibrator Kit is a liquid, ready-for-use calibrator based on human serum. It is a single level calibrator with lot specific values and diluted on board the analyzer to create a 5-point calibration curve. Control: The Homocysteine Control Kit consists of two ready-for-use controls based on human serum. The adjusted concentrations of the control components are in the low range for Control 1 and in the elevated range for Control 2.

The 3-Reagent Homocysteine Assay for Beckman Coulter SYNCHRON® and UniCel® systems is intended for in vitro quantitative determination of total homocysteine in human serum and plasma. The device can assist in the diagnosis and treatment of patients suspected of having hyperhomocysteinemia and homocystinuria.

Bound or dimerised homocysteine (oxidised form) is reduced to free homocysteine, which then reacts with serine catalysed by cystathionine beta-synthase (CBS) to form cystathionine. Cystathionine in turn is broken down by cystathionine beta-lyase (CBL) to form homocysteine, pyruvate and ammonia. Pyruvate is then converted by lactate dehydrogenase (LDH) to lactate with nicotinamide adenine dinucleotide (NADH) as coenzyme. The rate of NADH conversion to NAD+ is directly proportional to the concentration of homocysteine (delta A340 nm).

The Liquid Stable (LS) 2-Part Homocysteine Reagent is intended for in vitro quantitative determination of total homocysteine in human serum and plasma. The device can assist in the diagnosis and treatment of patients suspected of having hyperhomocysteinemia and homocystinuria.

The Axis-Shield Liquid Stable (LS) 2-Part Homocysteine Reagent Test System includes two reagents and two calibrators. The first reagent (Reag 1) includes Lactate dehydrogenase (LDH), Serine, nicotinamide adenine dinucleotide reduced di-sodium salt (NADH), tris [2-carboxyethyl] phosphine (TCEP) reductant, with buffers and stabilizers (Trizma Base and Trizma Hydrochloride), and preservative (Sodium Azide). The second reagent (Reag2) includes Cystathionine beta-Synthase (CBS) and Cystathionine beta-Lvase (CBL) cvcling enzymes with preservative (sodium azide). The Axis-Shield Liquid Stable (LS) 2-Part Homocysteine Reagent kit will also include two calibrators; Calibrator "0" (0 µmol/L) and Calibrator "28" (28 µmol/L).

The A/C Portable Enzymatic Homocysteine Assay on the A/C Diagnostics Reader (HyTek-205) is intended for the quantitative determination of total homocysteine (tHCY) in human plasma or serum. The device can assist in the diagnosis and treatment of patients suspected of having hyperhomocysteinemia. The A/C Enzymatic Homocysteine Assay is for in vitro diagnostic use.

The A/C Portable Enzymatic Homocysteine Assay is calibrated with A/C Enzymatic Homocysteine Assay Calibrators. A/C Enzymatic Homocysteine Assay Controls are assayed for the verification of the accuracy and precision of the A/C Portable Enzymatic Homocysteine Assay. The A/C Enzymatic Homocysteine Assay measures tHCY. The principle of the assay is that after reduction, tHCY is depleted by Homocysteinase (rHCYase) and produces hydrogen sulfide (H2S), which is determined using N.N-dibutyl phenylene diamine (DBPDA), the combination of which forms a chromophore, the fluorescence is measured by the A/C Diagnostics Reader (HyTek-205). The A/C Portable Enzymatic Homocysteine Assay is a three-steps reaction, which runs at room temperature. The total assay takes 80 minutes, and the A/C Diagnostics Reader is the only equipment needed.

The ARCHITECT Homocysteine assay is a chemiluminescent microparticle immunoassay (CMIA) for the quantitative determination of total L-homocysteine in human serum or plasma on the ARCHITECT i System. Homocysteine values can assist in the diagnosis and treatment of patients suspected of having hyperhomocysteinemia and homocystinuria. The ARCHITECT Homocysteine Calibrators are for the calibration of the ARCHITECT i System when used for the quantitative determination of total L-homocysteine in human serum or plasma. The ARCHITECT Homocysteine Controls are for the estimation of test precision and the detection of systematic analytical deviations of the ARCHITECT i System (reagents, calibrators and instrument), when used for the quantitative determination of total L-homocysteine in human serum or plasma. For in vitro diagnostic use.

The ARCHITECT Homocysteine assay is a one-step immunoassay for the quantitative determination of total L-homocysteine in human serum or plasma using CMIA technology, with flexible assay protocols, referred to as Chemiflex. Bound or dimerised homocysteine (oxidized form) is reduced by dithiothreitol (DTT) to free homocysteine, which is then converted to Sadenosyl homocysteine (SAH) by the action of the recombinant enzyme S-adenosyl homocysteine hydrolase (rSAHHase) in the presence of excess adenosine. The SAH then competes with acridinium-labeled S-adenosyl cysteine for particle-bound monoclonal antibody. Following a wash stage and magnetic separation, pre-trigger and trigger solutions are added to the reaction mixture and the resulting chemiluminescence is measured as relative light units (RLUs). An indirect relationship exists between the amount of homocysteine in the sample and the RLUs detected by the ARCHITECT i System optics.

Diazyme homocysteine 2 reagent assay is intended for the in vitro quantitative determination of total L-homocysteine in serum or plasma. For in-vitro diagnostic use only. The reagents can assist in the diagnosis and treatment of patients suspected of having hyperhomocyone . Inc creating and homocystinuria. Patients who are taking methotrexate, carbamazepine, phenytoin, nitrovos oxide, anticonvulsants, or 6-azuridine triacetate, may have higher levels of Homocysteine due to metabolic interference with Homocysteine metabolism. Diazyme homocysteine Calibrators is intended for the in vitro quantitative determination of total L-homocysteine in serum or plasma. For in-vitro diagnostic use only.

Not Found

Teco Enzymatic Homocysteine Assay is in vitro quantitative determination of total homocysteine in serum and plasma. Homocysteine measurements are used in the diagnostics and treatment of hyperhomocysteinemia.

Not Found