(137 days)
The Powder Free Nitrile Examination Gloves, Blue, Test For Use With Chemotherapy Drugs is a disposable device intended for medical purposes that is worn on the examiner's hand or finger to prevent contamination between patient and examiner. In addition, these gloves were tested for use with chemotherapy drugs in accordance with ASTM D6978-05 (2019) Standard Practice for Assessment of Medical gloves to Permeation by Chemotherapy Drugs.
The powder free Nitrile Examination glove is a disposable Class 1 medical device made of Nitrile rubber, and is intended for medical purposes that is worn on the examiner's hands to prevent contamination between patient and examiner. The principal operation of the medical device to provide single use barrier protection for the wearer and the device meets all the requirement specifications for Barrier Protection, tensile properties as defined in ASTM D6319-19, Standard specification for Nitrile Examination Gloves for medical Application.
The provided document describes the acceptance criteria and performance data for "Powder Free Nitrile Examination Gloves, Blue, Test For Use With Chemotherapy Drugs" (K213306), a Class I medical device.
Note: The document is for a medical device (gloves), not an AI/Software as a Medical Device (SaMD). Therefore, many of the typical acceptance criteria and study components for AI/SaMD (e.g., ground truth establishment by experts, MRMC studies, effect size of AI assistance, training set details) are not applicable or provided in this context. The information provided focuses on the physical and chemical performance of the gloves.
Here's an breakdown of the available information regarding acceptance criteria and device performance:
1. A table of acceptance criteria and the reported device performance
The primary acceptance criteria are based on various ASTM and ISO standards for examination gloves and chemotherapy drug permeation.
| Test Method | Purpose | Acceptance Criteria | Reported Device Performance and Results |
|---|---|---|---|
| ASTM D5151 | Water tightness Test for Detection of Holes | Meet the requirements of ASTM D5151 AQL 2.5 | Pass: Total 200 pcs of gloves were tested, 0 pcs rejected. |
| ASTM D6319 | Physical Dimensions Test | Length(mm): S: ≥220 mm; M/L/XL: ≥230 mm.Width(mm): S:80±10mm; M:95±10mm; L: 110±10mm; XL: 120±10mm.Thickness (mm): Finger: ≥0.05, Palm: ≥0.05 | Pass: 13 pcs each size, total 65 pcs of gloves were tested, 0 pcs rejected. |
| ASTM D412 | Physical properties (Tensile Strength & Ultimate Elongation) | Before Aging: Tensile Strength ≥14MPa, Ultimate Elongation ≥500%After Aging: Tensile Strength ≥14MPa, Ultimate Elongation ≥500% | Pass: 13 pcs each size, total 65 pcs of gloves were tested, 0 pcs rejected. |
| ASTM D6124 | Residual Powder Content | Meet the requirements of ASTM D6124 < 2.0mg | Pass: 5 pcs each size, total 25 pcs of gloves were tested, 0 pcs rejected. |
| ISO 10993-10 | Skin irritation | non-irritating | Pass: The test result showed that the response of the test article extract was categorized as negligible under the test condition. |
| ISO 10993-10 | Skin Sensitization | non-sensitizing | Pass: Under the conditions of this study, the test article extract showed no significant evidence of causing skin sensitization in the guinea pig. The positive rate of sensitization was 0%. No evidence of skin sensitization in guinea pigs was found. |
| ISO 10993-5 | Cytotoxicity | Non-cytotoxicity. | Pass: Under the conditions of this study, the test article extract did not show potential toxicity to L929 cells. |
| ASTM D6978-05 (2019) | Chemotherapy Drug Permeation (Breakthrough Detection Time) | Varies by drug (e.g., >240 minutes for most, with specific lower times for Carmustine and Thio Tepa) | |
| Carmustine (BCNU) | 3.3 mg/ml (3,300 ppm) | No explicit minimum acceptance criterion listed for Carmustine, but the reported value is a key performance metric. | 16.9 minutes |
| Cisplatin | 1.0 mg/ml(1,000 ppm) | >240 minutes | >240 minutes |
| Cyclophosphamide (Cytoxan) | 20 mg/ml(20,000 ppm) | >240 minutes | >240 minutes |
| Dacarbazine | 10 mg/ml(10,000 ppm) | >240 minutes | >240 minutes |
| Doxorubicin HCl | 2.0 mg/ml(2,000 ppm) | >240 minutes | >240 minutes |
| Eotoside (Toposar) | 20.0 mg/ml(20,000 ppm) | >240 minutes | >240 minutes |
| Fluorouracil | 50.0 mg/ml(50,000 ppm) | >240 minutes | >240 minutes |
| Mechlorethamine | 1.0 mg/ml(1,000 ppm) | >240 minutes | >240 minutes |
| Methotrexate | 25.0 mg/ml(25,000 ppm) | >240 minutes | >240 minutes |
| Mitomycin C | 0.5 mg/ml(500 ppm) | >240 minutes | >240 minutes |
| Paclitaxel (Taxol) | 6.0 mg/ml(6,000 ppm) | >240 minutes | >240 minutes |
| Thio Tepa | 10.0 mg/ml(10,000 ppm) | No explicit minimum acceptance criterion listed for Thio Tepa, but the reported value is a key performance metric. | 22.6 minutes |
| Vincristine Sulfate | 1.0 mg/ml(1,000 ppm) | >240 minutes | >240 minutes |
2. Sample sizes used for the test set and the data provenance
- ASTM D5151 (Water tightness): 200 pieces of gloves.
- ASTM D6319 (Physical Dimensions): 13 pieces for each size (total 65 pieces: S, M, L, XL, and presumably X-Small from the comparison table, although the specific breakdown adds up to 5 sizes * 13 = 65).
- ASTM D412 (Physical Properties): 13 pieces for each size (total 65 pieces).
- ASTM D6124 (Residual Powder Content): 5 pieces for each size (total 25 pieces).
- ISO 10993-10 (Skin irritation/sensitization) & ISO 10993-5 (Cytotoxicity): The specific number of test subjects (e.g., guinea pigs for sensitization, L929 cells for cytotoxicity) is not explicitly stated, but standard animal models and cell lines are typically used.
- ASTM D6978-05 (Chemotherapy Drug Permeation): The specific sample size for each drug permeation test is not explicitly stated in this summary. However, these are bench tests.
Data Provenance: The document does not specify the country of origin for the testing data beyond the manufacturer being in China. The tests are "Performance Testing (Bench)" and "Biocompatibility Testing," indicating they are laboratory-based studies. The nature of these tests means they are prospective in the sense that the testing was conducted specifically to evaluate the performance of these gloves against the specified standards.
3. Number of experts used to establish the ground truth for the test set and the qualifications of those experts
This section is not applicable as the device is a physical medical glove and not an AI/Software as a Medical Device (SaMD) that would rely on expert interpretation of medical images or data for ground truth. The "ground truth" for these tests is the objective measurement against established physical/chemical standards (e.g., a hole detected by water, a specific tensile strength value, a chemical permeation time).
4. Adjudication method for the test set
This is not applicable. The tests are objective measurements against established standards, not subjective interpretations requiring reader adjudication.
5. If a multi-reader multi-case (MRMC) comparative effectiveness study was done, If so, what was the effect size of how much human readers improve with AI vs without AI assistance
This is not applicable. This is a device (glove) that does not involve human readers interpreting data or AI assistance.
6. If a standalone (i.e. algorithm only without human-in-the-loop performance) was done
This is not applicable. This is a physical device, not an algorithm.
7. The type of ground truth used
The ground truth used for these studies is based on accepted international and national consensus standards for medical gloves and their performance (ASTM D5151, ASTM D6319, ASTM D412, ASTM D6124, ISO 10993-10, ISO 10993-5, and ASTM D6978-05). It is not expert consensus, pathology, or outcomes data in the typical sense of a diagnostic medical device. It's objective measurement against defined physical and chemical criteria.
8. The sample size for the training set
This is not applicable. This is a physical medical device, not an AI model that requires a training set.
9. How the ground truth for the training set was established
This is not applicable for the reasons stated above.
{0}------------------------------------------------
Image /page/0/Picture/0 description: The image shows the logo of the U.S. Food and Drug Administration (FDA). The logo consists of two parts: the Department of Health & Human Services logo on the left and the FDA logo on the right. The FDA logo is in blue and includes the letters "FDA" in a square and the words "U.S. Food & Drug Administration".
February 18, 2022
Zibo Sinocare Plastic Products Co., Ltd Mila Guo Operation Manager Lot 5, No. 21 Qingtian Road Zibo, Shandong 255414 China
Re: K213306
Trade/Device Name: Powder Free Nitrile Examination Gloves, Blue, Test For Use With Chemotherapy Drugs Regulation Number: 21 CFR 880.6250 Regulation Name: Non-Powdered Patient Examination Glove Regulatory Class: Class I, reserved Product Code: LZA, LZC Dated: January 7, 2022 Received: January 27, 2022
Dear Mila Guo:
We have reviewed your Section 510(k) premarket notification of intent to market the device referenced above and have determined the device is substantially equivalent (for the indications for use stated in the enclosure) to legally marketed predicate devices marketed in interstate commerce prior to May 28, 1976, the enactment date of the Medical Device Amendments, or to devices that have been reclassified in accordance with the provisions of the Federal Food, Drug, and Cosmetic Act (Act) that do not require approval of a premarket approval application (PMA). You may, therefore, market the device, subject to the general controls provisions of the Act. Although this letter refers to your product as a device, please be aware that some cleared products may instead be combination products. The 510(k) Premarket Notification Database located at https://www.accessdata.fda.gov/scripts/cdrh/cfdocs/cfpmn/pmn.cfm identifies combination product submissions. The general controls provisions of the Act include requirements for annual registration, listing of devices, good manufacturing practice, labeling, and prohibitions against misbranding and adulteration. Please note: CDRH does not evaluate information related to contract liability warranties. We remind you, however, that device labeling must be truthful and not misleading.
If your device is classified (see above) into either class II (Special Controls) or class III (PMA), it may be subject to additional controls. Existing major regulations affecting your device can be found in the Code of Federal Regulations, Title 21, Parts 800 to 898. In addition, FDA may publish further announcements concerning your device in the Federal Register.
Please be advised that FDA's issuance of a substantial equivalence determination does not mean that FDA has made a determination that your device complies with other requirements of the Act or any Federal
{1}------------------------------------------------
statutes and regulations administered by other Federal agencies. You must comply with all the Act's requirements, including, but not limited to: registration and listing (21 CFR Part 807); labeling (21 CFR Part 801); medical device reporting of medical device-related adverse events) (21 CFR 803) for devices or postmarketing safety reporting (21 CFR 4, Subpart B) for combination products (see https://www.fda.gov/combination-products/guidance-regulatory-information/postmarketing-safety-reportingcombination-products); good manufacturing practice requirements as set forth in the quality systems (QS) regulation (21 CFR Part 820) for devices or current good manufacturing practices (21 CFR 4, Subpart A) for combination products; and, if applicable, the electronic product radiation control provisions (Sections 531-542 of the Act); 21 CFR 1000-1050.
Also, please note the regulation entitled, "Misbranding by reference to premarket notification" (21 CFR Part 807.97). For questions regarding the reporting of adverse events under the MDR regulation (21 CFR Part 803), please go to https://www.fda.gov/medical-device-safety/medical-device-reportingmdr-how-report-medical-device-problems.
For comprehensive regulatory information about medical devices and radiation-emitting products, including information about labeling regulations, please see Device Advice (https://www.fda.gov/medicaldevices/device-advice-comprehensive-regulatory-assistance) and CDRH Learn (https://www.fda.gov/training-and-continuing-education/cdrh-learn). Additionally, you may contact the Division of Industry and Consumer Education (DICE) to ask a question about a specific regulatory topic. See the DICE website (https://www.fda.gov/medical-device-advice-comprehensive-regulatoryassistance/contact-us-division-industry-and-consumer-education-dice) for more information or contact DICE by email (DICE@fda.hhs.gov) or phone (1-800-638-2041 or 301-796-7100).
Sincerely,
Clarence W. Murray, III, PhD Assistant Director DHT4B: Division of Infection Control and Plastic Surgery Devices OHT4: Office of Surgical and Infection Control Devices Office of Product Evaluation and Quality Center for Devices and Radiological Health
Enclosure
{2}------------------------------------------------
DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration
Indications for Use
510(k) Number (if known) K213306
Device Name
Powder Free Nitrile Examination Gloves, Blue, Test For Use With Chemotherapy Drugs
Indications for Use (Describe)
The Powder Free Nitrile Examination Gloves, Blue, Test For Use With Chemotherapy Drugs is a disposable device intended for medical purposes that is worn on the examiner's hand or finger to prevent contamination between patient and examiner. In addition, these gloves were tested for use with chemotherapy drugs in accordance with ASTM D6978-05 (2019) Standard Practice for Assessment of Medical gloves to Permeation by Chemotherapy Drugs:
| Test Chemotherapy Drug | Concentration | Breakthrough Detection Time in Minutes |
|---|---|---|
| Carmustine (BCNU) | 3.3 mg/ml (3,300 ppm) | 16.9 |
| Cisplatin | 1.0 mg/ml(1,000 ppm) | >240 |
| Cyclophosphamide (Cytoxan) | 20 mg/ml(20,000 ppm) | >240 |
| Dacarbazine | 10 mg/ml(10,000 ppm) | >240 |
| Doxorubicin HCl | 2.0 mg/ml(2,000 ppm) | >240 |
| Eotoside (Toposar) | 20.0 mg/ml(20,000 ppm) | >240 |
| Fluorouracil | 50.0 mg/ml(50,000 ppm) | >240 |
| Mechlorethamine | 1.0 mg/ml(1,000 ppm) | >240 |
| Methotrexate | 25.0 mg/ml(25,000 ppm) | >240 |
| Mitomycin C | 0.5 mg/ml(500 ppm) | >240 |
| Paclitaxel (Taxol) | 6.0 mg/ml(6,000 ppm) | >240 |
| Thio Tepa | 10.0 mg/ml(10,000 ppm) | 22.6 |
| Vincristine Sulfate | 1.0 mg/ml(1,000 ppm) | >240 |
Please note that the following drugs have low permeation times: Carmustine (BCNU) 3.3mg/ml 16.9 Minutes Thio Tepa 10.0 mg/ml 22.6 Minutes.
Warning: Don't to use with either Carmustine or Thio Tepa
Type of Use (Select one or both, as applicable)
| | Prescription Use (Part 21 CFR 801 Subpart D)
X Over-The-Counter Use (21 CFR 801 Subpart C)
CONTINUE ON A SEPARATE PAGE IF NEEDED.
This section applies only to requirements of the Paperwork Reduction Act of 1995.
DO NOT SEND YOUR COMPLETED FORM TO THE PRA STAFF EMAIL ADDRESS BELOW.
The burden time for this collection of information is estimated to average 79 hours per response, including the time to review instructions, search existing data sources, gather and maintain the data needed and complete and review the collection of information. Send comments regarding this burden estimate or any other aspect of this information collection, including suggestions for reducing this burden, to:
Department of Health and Human Services Food and Drug Administration Office of Chief Information Officer Paperwork Reduction Act (PRA) Staff PRAStaff(@fda.hhs.gov
"An agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a currently valid OMB number."
{3}------------------------------------------------
510 (k) SUMMARY
(K213306)
This summary of K213306 is being submitted in accordance with 21 CFR 807.92
1.0 Submitter's Information
| Submitter Name: | Zibo Sinocare Plastic Products Co., Ltd |
|---|---|
| Registration Number: | 3005060582 |
| Address: | Lot 5, No. 21 Qingtian Road, Zibo, Shandong, China 255414 |
| Contact Person & Title: | Mila Guo, Operation Manager |
| Contact: Tel & Fax : | +86-533-7859433 |
| Email: | sinocare2000@126.com |
Summary Preparation Date: Feb 10, 2022
2.0 Name of the Device
| Proprietary/Trade name: | Powder Free Nitrile Examination Gloves, Blue, Tested ForUse With Chemotherapy Drugs |
|---|---|
| Common Name: | Patient Examination Gloves, Nitrile, Powder free |
| Classification Name: | Non-Powdered Patient Examination Glove |
| Device Classification: | Class 1 |
| Regulation Number: | 21 CFR 880.6250 |
| Product Code: | LZA, LZC |
3.0 Predicate device
| Primary Device Name: | Nitrile Exam Gloves, Powder Free, Blue (Tested for Usewith Chemotherapy Drugs) |
|---|---|
| Company name: | Hengchang (Dongying) Medical Technology Co., Ltd. |
| 510(K) Number: | K211714 |
4.0 Device Description:
The powder free Nitrile Examination glove is a disposable Class 1 medical device made of Nitrile rubber, and is intended for medical purposes that is worn on the examiner's hands to prevent contamination between patient and examiner. The principal operation of the medical device to provide single use barrier protection for the wearer and the device meets
{4}------------------------------------------------
all the requirement specifications for Barrier Protection, tensile properties as defined in ASTM D6319-19, Standard specification for Nitrile Examination Gloves for medical Application.
5.0 Indication for use:
The Powder Free Nitrile Examination Gloves, Blue, Tested For Use With Chemotherapy Drugs is a disposable device intended for medical purposes that is worn on the examiner's hand or finger to prevent contamination between patient and examiner.
In addition, these gloves were tested for use with chemotherapy drugs in accordance with ASTM D6978-05 (2019) Standard Practice for Assessment of Medical gloves to Permeation by Chemotherapy Drugs:
| No. | Test Chemotherapy Drugs | Concentration | Minimum BreakthroughDetection Time in Minutes |
|---|---|---|---|
| 1 | Carmustine (BCNU) | 3.3 mg/ml (3,300 ppm) | 16.9 |
| 2 | Cisplatin | 1.0 mg/ml(1,000 ppm) | >240 |
| 3 | Cyclophosphamide | 20 mg/ml(20,000 ppm) | >240 |
| 4 | Dacarbazine | 10 mg/ml(10,000 ppm) | >240 |
| 5 | Doxorubicin HCI | 2.0 mg/ml(2,000 ppm) | >240 |
| 6 | Eotoside (Toposar) | 20.0 mg/ml(20,000 ppm) | >240 |
| 7 | Fluorouracil | 50.0 mg/ml(50,000 ppm) | >240 |
| 8 | Mechlorethamine | 1.0 mg/ml(1,000 ppm) | >240 |
| 9 | Methotrexate | 25.0 mg/ml(25,000 ppm) | >240 |
| 10 | Mitomycin C | 0.5 mg/ml(500 ppm) | >240 |
| 11 | Paclitaxel (Taxol) | 6.0 mg/ml(6,000 ppm) | >240 |
| 12 | Thio Tepa | 10.0 mg/ml(10,000 ppm) | 22.6 |
| 13 | Vincristine Sulfate | 1.0 mg/ml(1,000 ppm) | >240 |
Please note that the following drugs have low permeation times:
Carmustine (BCNU) 3.3 mg/ml 16.9 Minutes;
Thio Tepa 10.0 mg/ml 22.6 Minutes.
Warning: Do not use with either Carmustine or Thio Tepa
{5}------------------------------------------------
6.0 Technological Characteristics Comparison Table
Shown below is a technological comparison of the subject device (K213306) with the
| Items | Predicate Device: K211714 | Subject Device: K213306 | Comparison | |
|---|---|---|---|---|
| Product Code | LZA, LZC | LZA, LZC | Same | |
| Device Class | Class I | Class I | Same | |
| Indication for use(IFU) | A patient examination glove isa disposable device intendedfor medical purposes that isworn on the examiner's handsto prevent contaminationbetween patient and examiner.These gloves were tested foruse with chemotherapy drugs,per ASTM D6978-05 StandardPractice for Assessment ofResistance of Medical Glovesto Permeation byChemotherapy Drugs. | The Powder Free NitrileExamination Gloves, Blue,Tested For Use WithChemotherapy Drugs is adisposable device intended formedical purposes that is worn onthe examiner's hand or finger toprevent contamination betweenpatient and examiner. In addition,these gloves were tested for usewith chemotherapy drugs inaccordance with ASTMD6978-05 (2019) StandardPractice for Assessment ofMedical gloves to Permeation byChemotherapy Drugs. | Similar | |
| Regulation No | 21 CFR 880.6250 | 21 CFR 880.6250 | Same | |
| Powder free | yes | yes | Same | |
| Design Feature | Ambidextrous | Ambidextrous | Same | |
| Sterility | Non-Sterile | Non-Sterile | Same | |
| Material | Nitrile | Nitrile | Same |
predicate device (K211714) .Table 1- General Comparison:
{6}------------------------------------------------
| Former ReleaseChemical | Calcium Stearate Dispersion | Calcium Stearate Dispersion | Same |
|---|---|---|---|
| DeviceDescription andSpecifications | Comply with ASTM D6319-19 | Comply with ASTM D6319-19 | Similar |
| Label andLabeling | Single-use indication, powderfree, device color, device name,glove size and quantity,Non-Sterile, a statement ofstandard ASTM D6978-05compliance and a summary ofthetesting results. | Single-use indication, powderfree, device color, device name,glove size and quantity,Non-Sterile, a statement ofstandard ASTM D6978-05(2019) compliance and asummary of the testing results. | Same |
1) Table 2- Device Dimension and Performance Comparison
| Items | Predicate Device: K211714 | Subject Device: K213306 | Comparison |
|---|---|---|---|
| Color | White, Blue | Blue | Similar, Note 1 |
| Lengthmm | Complies with ASTM D6319-19:S: $\u2265$ 220 mm; M/L/XL: $\u2265$ 230 mm. | Minimum 230 mm | Similar |
| Palm | Complies with ASTM D6319-19Palm: $\u2265$ 0.05mm | 0.08+/-0.03 mm | |
| Cuff | 0.08+/-0.03 mm | Similar, Note 2 | |
| Finger | Complies with ASTM D6319-19Finger: $\u2265$ 0.05mm | 0.08+/-0.03mm | |
| Before aging | Complies with ASTM D6319-19:$\u2265$ 500% | 500% min | Same |
| After aging | $\u2265$ 400% min | 400% min | Same |
| Before aging | Complies with ASTM D6319-19$\u2265$ 14MPa | 15MPa min | Similar |
| After aging | $\u2265$ 14MPa | 14MPa min | Same |
| Palm width(mm) | Complies with ASTMD6319-19: | X-Small: 70+/- 10mm | Same |
| S:80±10mm; | Small:80 +/- 10mm | ||
| M:95±10mm; | Medium: 95+/- 10mm | ||
| L: 110±10mm; | Large:110 +/- 10mm | ||
| XL: 120±10mm; | X-large: 120 +/- 10mm | ||
| Freedom frompinholes | Complies with ASTM D6319-19and ASTM D5151-19 G-1, AQL2.5 | Be free from holes when testedin accordance with ASTMD5151, and meet the standardASTM D6319 | Same |
| Residual powder | Complies with ASTM D6319-19,< 2 mg per glove | Meet ASTM D6124-06 (2017)Results generated valuesbelow 2 mg of residual powder,meet the requirement of ASTMD6319. | Similar, allmeetASTMD6319. |
| Chemotherapydrugs testedwith minimumBreakthroughDetection Timeas Tested perASTM D6978 | Carmustine (BCNU), 3.3 mg/ml ,23.6 min | Carmustine (BCNU),3.3 mg/ml ,16.9mins | Similar note 3 |
| Cisplatin 1 mg/ml , > 240 mins | Cisplatin, 1.0mg/ml, >240 mins | Same | |
| Cyclophosphamide, 20 mg/ml ,>240 mins | Cyclophosphamide (Cytoxan),20.0 mg/ml, >240 mins | Same | |
| Dacarbazine (DTIC), 10.0 mg/ml,>240 min | Dacarbazine (DTIC),10.0 mg/ml, >240 mins | Same | |
| Doxorubicin Hydrochloride, 2.0mg/ml, >240 min | Doxorubicin Hydrochloride,2.0 mg/ml, >240 mins | Same | |
| Etoposide (Toposar), 20.0 mg/ml,>240 min | Eotoposide (Toposar),20.0 mg/ml, >240 mins | Same | |
| Fluorouracil, 50.0 mg/ml, > 240min | Fluorouracil, 50.0mg/ml,> 240 mins | Same | |
| / | Mechlorethamine, 1.0 mg/ml,> 240 mins | Meet ASTMD6978 | |
| Methotrexate 25 mg/ml,> 240min | Methotrexate, 25.0 mg/ml,> 240 mins | Same | |
| Mitomycin C 0.5 mg/ml,> 240min | Mitomycin C, 0.5 mg/ml,>240 min | Same | |
| Paclitaxel, 6.0 mg/ml, >240 min | Paclitaxel (Taxol), 6.0 mg/ml,> 240 mins | Same | |
| Thiotepa, 10.0 mg/ml 57.4mins ,Vincristine Sulfate 1.0 mg/ml, >240 min | Thiotepa, 10.0 mg/ml, 22.6 minsVincristine Sulfate, 1.0 mg/ml,> 240 mins | Similar note 3Same |
{7}------------------------------------------------
{8}------------------------------------------------
Notes:
-
The color of the subject device is different with that of the predicate. The subject device was evaluated according to ISO 10993-1 standards.
-
The physical properties are a little different with that of the predicate, but they all meet the requirements of ASTM D6319-19.
-
Breakthrough detection times of Carmustine (BCNU) and Thio Tepa are different. The IFU Statement has clearly defined on the labeling.
2) Table 3- Biocompatibility Testing
| Bio-compatibility | Items | Predicate Device: K211714 | Subject Device: K213306 | Remark |
|---|---|---|---|---|
| Irritation (ISO10993-10:2010BiologicalEvaluation ofMedical Devices-Part 10: Tests ForIrritation And SkinSensitization) | Complies with ISO 10993-10(2010)*Under the conditions of thestudy, the device is anonirritant and anon-sensitizer. | The test result showed thatthe response of the testarticle extract wascategorized as negligibleunder the test condition. | Same | |
| Sensitization (ISO10993-10:2010BiologicalEvaluation ofMedical Devices -Part 10: Tests ForIrritation And SkinSensitization) | Under the conditions of thisstudy, the test article extractshowed no significantevidence of causing skinsensitization in the guineapig. The positive rate ofsensitization was 0%. Noevidence of skin sensitizationin guinea pigs was found. | Same | ||
| Cytotoxicity (ISO10993-5:2009BiologicalEvaluation ofMedical Devices-Part 5: Tests For InVitro Cytotoxicity) | Complies with ISO 10993-5(2009)* Under the conditions of thestudy, the device is notcytotoxic. | Under the conditions of thisstudy, the test article extractdid not show potential toxicityto L929 cells. | Same |
{9}------------------------------------------------
| 7.0 Summary of Non-Clinical Performance Data: | |
|---|---|
| ----------------------------------------------- | -- |
| Test Method | Purpose | Acceptance Criteria | Results |
|---|---|---|---|
| ASTM D5151 | Water tightnessTest for Detectionof Holes | Meet the requirements of ASTMD5151 AQL 2.5 | PassTotal 200 pcs of gloves weretested, 0 pcs rejected |
| ASTM D6319 | PhysicalDimensions Test | Length(mm):S: ≥220 mm;M/L/XL: ≥230 mm.Width(mm):S:80±10mm;M:95±10mm;L: 110±10mm;XL: 120±10mm.Thickness (mm):Finger: ≥0.05Palm: ≥0.05 | Pass13 pcs each size,total 65pcs of gloves were tested, 0pcs rejected. |
| ASTM D412 | Physical properties | Before AgingTensile Strength ≥14MPaUltimate Elongation ≥500%After AgingTensile Strength ≥14MPaUltimate Elongation≥500% | Pass13 pcs each size, total 65pcs of gloves were tested, 0pcs rejected. |
| ASTM D6124 | Residual PowderContent | Meet the requirements of ASTMD6124 < 2.0mg | Pass5 pcs each size, total 25 pcsof gloves were tested, 0 pcsrejected. |
| ISO 10993-10 | Skin irritation | non-irritating | PassThe test result showed thatthe response of the testarticle extract wascategorized as negligibleunder the test condition. |
| ISO 10993-10 | Skin Sensitization | non-sensitizing | PassUnder the conditions of thisstudy, the test article extractshowed no significantevidence of causing skin |
| sensitization in the guineapig. The positive rate ofsensitization was 0%. Noevidence of skinsensitization in guinea pigswas found. | |||
| ISO 10993-5 | Cytotoxicity | Non-cytotoxicity. | PassUnder the conditions of thisstudy, the test article extractdid not show potentialtoxicity to L929 cells. |
{10}------------------------------------------------
Biocompatibility Testing
The biocompatibility evaluation for Nitrile Exam Gloves, Powder Free, Blue, Tested for Use with Chemotherapy was conducted in accordance with the following standards: ISO 10993-10:2010 Biological Evaluation of Medical Devices - Part 10: Tests for Irritation And Skin Sensitization.
ISO 10993-5:2009 Biological Evaluation of Medical Devices - Part 5: Tests For In Vitro Cytotoxicity
Performance Testing (Bench)
Physical performance qualities of the Subject Device were evaluated per ASTM D6319-19, Standard Specification for Nitrile Examination Gloves for Medical Application.
Permeation testing was conducted to support the addition of the labeling claim: Tested for use with chemotherapy drugs. In addition, the Subject Device was tested according to ASTM D6978-05 (Reapproved 2019), Standard Practice for Assessment of Resistance of Medical Gloves to Permeation by Chemotherapy Drugs, in which minimum breakthrough times were determined for a wide range of chemotherapy drugs.
In summary, the performance testing of the subject device was conducted to adequately demonstrate the device met the acceptance criteria in the relevant test methods cited below:
{11}------------------------------------------------
-
ASTM D6124-06 (Reapproved 2017), Standard Test Method for Residual Powder on Medical Gloves
-
ASTM D5151-19, Standard Test Method for Detection of Holes in Medical Gloves.
-
ASTM D6319-19, Standard Specification for Nitrile Examination Gloves for Medical Application.
-ASTM D 6978-05 (Reapproved 2019) Standard Practice for Assessment of Resistance of Medical Gloves to Permeation by Chemotherapy Drugs.
8.0 Summary of Clinical Test:
Clinical data was not needed for this device.
9.0 Conclusion:
Based on the nonclinical tests data, it can be concluded that the Disposable Powder Free Nitrile Examination Glove, Blue, Tested For Use With Chemotherapy Drugs is as safe, as effective, and performs as well as or better than the legally marketed predicated device under K211714.
§ 880.6250 Non-powdered patient examination glove.
(a)
Identification. A non-powdered patient examination glove is a disposable device intended for medical purposes that is worn on the examiner's hand or finger to prevent contamination between patient and examiner. A non-powdered patient examination glove does not incorporate powder for purposes other than manufacturing. The final finished glove includes only residual powder from manufacturing.(b)
Classification. Class I (general controls). The device, when it is a finger cot, is exempt from the premarket notification procedures in subpart E of part 807 of this chapter subject to the limitations in § 880.9.