Search Results

CONELOG® Implant System Implants are intended for immediate or delayed placement in the bone of the maxillary or mandibular arch. CONELOG® Implant System Abutments are intended for use as support for crowns, bridges or overdentures. When a one-stage surgical approach is applied, the implant may be immediately loaded when good primary stability is achieved and the functional load is appropriate.

CONELOG® Implants with 3.3 mm diameter have the following additional specific indications:
These are an alternative in cases where the alveolar ridge width is only 5 - 6 mm. Because of their lower mechanical strength compared with larger diameter implants, they should only be used under the following conditions:

• As single implants, they should be used only to replace mandibular incisors and/or maxillary lateral incisors.
• An edentulous arch can only be restored with a bar retained superstructure with at least four implants of 3.3 mm diameter without distal extensions.
• Implants of Ø 3.3 mm are suitable for a partially edentulous arch when combined with implants of larger diameter for splinted superstructures. However, the limited strength of the implants with Ø 3.3 mm must be taken into account.
• Avoid excessive mechanical stressing of the implants when using ball abutments in combination with Ø 3.3 mm implants.
• The healing time for Ø 3.3 mm implants is at least 12 weeks.

CONELOG® Implants with 7 mm length have the following additional specific indications:
CONELOG® SCREW-LINE Implants should only be used when there is not enough space for a longer implant. Delayed loading in single tooth replacement is indicated with these implants. If the ratio of crown length to implant length is unfavorable the biomechanical risk factors have to be considered and appropriate measures have to be taken by the dental professional.

Abutment Indications for Use
CONELOG® Abutments are intended to be used to fabricate prosthetic restorations in conjunction with CONELOG implants to support prostheses in the maxillary and/or mandibular arch.

Vario SR Indications for Use
CONELOG® Vario SR components for crown and bridge restorations:

• Occlusal screw-retained crown, bridge and bar constructions on CONELOG® implants in the anterior and posterior region of the maxilla and mandible
  CONELOG® Vario SR components for bar restorations:
• Anchorage of implant-supported full dentures for the edentulous maxilla in conjunction with 4 or more CONELOG® implants and in the edentulous mandible in conjunction with 2 or 4 or more CONELOG® implants.

The purpose of this submission is to add an alternative to the CAMLOG® Implant System by the introduction of an implant line with a tapered implant abutment interface. The new line of implants and abutments is named the CONELOG® Implant System. The primary features of the current CAMLOG Implant System are a change from the tube-in-tube interface with a square cam design for anti-rotation to the tapered implant/abutment interface connection with three positioning cams and the addition of a 7.0 mm long implant. The three positioning cams of the CONELOG abutments are placed more apically on the abutment shaft but are comparable in design principle to the three positioning cams of the CAMLOG Implant System. All other design features of the system remain the same.

The CONELOG implant system features an implant/abutment interface that includes a 7.5° taper with anti-rotation cams at the base of the connection. Components available with the CONELOG implant/abutment interface include the SCREW-LINE Promote® plus implant and cover screw, healing caps, Universal abutments, Telescope abutments, Esthomic" abutments, the Esthomice abutment inset, temporary abutments, Gold-plastic abutments, Logfit® abutments, ball abutments, bar abutments and Vario SR abutments. All components correspond to previously cleared CAMLOG components with the tube-in-tube interface.

The provided document is a 510(k) summary for a medical device (dental implant system) and does not contain information about acceptance criteria or a study proving device performance against such criteria. The document describes the device, its intended use, its equivalence to previously marketed devices, and the administrative information for its 510(k) clearance.

Therefore, I cannot extract the requested information as it is not present in the provided text.

Ask a specific question about this device