(105 days)
The probe is for use with the Deltex Medical CardioQ-EDM and CardioQ-EDM+ for Monitoring of cardiac output and fluid status. The probe is only approved for oral placement into the esophagus of a single anesthetized patient 15 years of age or younger, 50cm (20") to 170cm (67") in height.
The Deltex Medical Ltd KDP72 Pediatric Doppler Probe is an oral extravascular blood flow probe designed to work with the CardioQ-EDM and CardioQ-EDM+ Systems (K111542 and K132139 respectively). It consists of a shaft, which is a spring reinforced silicone tube, with an electrical connector on the machine end and an ultrasonic transmitting and receiving tip on the patient end. The tip is fully covered and sealed to the shaft with a silicone rubber boot and by wires running through the shaft to the connector. Visual product identification is provided at the machine end and the device is provided single packed sterile for single patient use.
The provided document is a 510(k) summary for the Deltex Medical KDP72 Doppler Probe, asserting its substantial equivalence to previously cleared devices. It describes the device, its intended use, and performance data related to its design and safety standards, but does not contain information about a study proving the device meets specific acceptance criteria related to its clinical performance as a diagnostic tool for cardiac output and fluid status.
The "Performance Data" section briefly mentions:
- "The performance data recommended in 'Information for Manufacturers Seeking Marketing Clearance of Diagnostic Ultrasound Systems and Transducers,' issued on September 9, 2008, has been included." This suggests that general requirements for diagnostic ultrasound devices were addressed, likely related to acoustic output and image quality, not the accuracy of cardiac output measurements.
- "Additionally a flexibility test has been conducted on the subject and predicate devices which demonstrates the comparative flexibility." This is a mechanical performance test, not a clinical diagnostic performance study.
Therefore, many of the requested categories for acceptance criteria and a study to prove they are met cannot be extracted from this document, as the document focuses on demonstrating substantial equivalence based on design, materials, sterilization, biocompatibility, and electrical safety standards rather than clinical diagnostic accuracy.
However, based on the provided text, here’s what can be extracted:
1. A table of acceptance criteria and the reported device performance
| Acceptance Criteria Category | Acceptance Criteria | Reported Device Performance (KDP72 Doppler Probe) |
|---|---|---|
| Sterilization | Sterilized in accordance with ISO 11135-1 (version of standard current at time of submission). | Meets ISO 11135-1 (version current at submission). |
| Shelf Life | Meets ISO 11607-1 (version of standard current at time of submission). | Meets ISO 11607-1 (version current at submission). |
| Biocompatibility | Tested in accordance with ISO 10993-5 (Cytotoxicity), ISO 10993-10 (Irritation and Skin Sensitization), ISO 10993-7 (Ethylene Oxide Sterilization Residuals) (version of standard current at time of submission). Note: ISO 10993-7 is about ETO residuals, not a direct biocompatibility test type, but often included for ETO sterilized devices. | Meets ISO 10993-5, ISO 10993-10, ISO 10993-7 (versions current at submission). |
| EMC and Electrical Safety | Meets IEC 60601-1 (Medical Electrical Equipment - General requirements for basic safety and essential performance), IEC 60601-1-2 (Electromagnetic disturbances - Requirements and tests), IEC 60601-2-37 (Particular requirements for the basic safety and essential performance of ultrasonic medical diagnostic and monitoring equipment) (version of standard current at time of submission). | Meets IEC 60601-1, IEC 60601-1-2, IEC 60601-2-37 (versions current at submission). |
| Packaging | Meets ISO 11607-1 (Packaging for terminally sterilized medical devices - Requirements for materials, sterile barrier systems and packaging systems), ISO 11607-2 (Packaging for terminally sterilized medical devices - Validation requirements for forming, sealing and assembly processes) (version of standard current at time of submission). | Meets ISO 11607-1, ISO 11607-2 (versions current at submission). |
| Flexibility | Demonstrates comparative flexibility to predicate devices. (No specific quantitative acceptance criterion stated). | Flexibility test conducted; demonstrates comparative flexibility. |
| Diagnostic Ultrasound Performance Data | Based on "Information for Manufacturers Seeking Marketing Clearance of Diagnostic Ultrasound Systems and Transducers", issued on September 9, 2008. (Likely relates to acoustic output, measurement accuracy of general ultrasound parameters, not necessarily cardiac output accuracy specifically). | "Included" (no specific results provided). |
2. Sample size used for the test set and the data provenance:
Not specified in the document for any clinical performance or diagnostic accuracy study. The document mentions a flexibility test, but details on sample size or provenance are not provided.
3. Number of experts used to establish the ground truth for the test set and the qualifications of those experts:
Not applicable/not specified. The document does not describe a study involving expert-established ground truth for clinical diagnostic performance.
4. Adjudication method for the test set:
Not applicable/not specified.
5. If a multi-reader multi-case (MRMC) comparative effectiveness study was done, If so, what was the effect size of how much human readers improve with AI vs without AI assistance:
Not applicable. This device is a probe for a cardiac output monitor, not an AI-assisted diagnostic imaging system that involves human readers.
6. If a standalone (i.e. algorithm only without human-in-the-loop performance) was done:
Not specified. The document refers to "performance data recommended in 'Information for Manufacturers Seeking Marketing Clearance of Diagnostic Ultrasound Systems and Transducers'" but does not detail what kind of study was performed or if it was standalone. The device is a probe to be used with a monitoring system, implying a system performance, not a standalone algorithm.
7. The type of ground truth used:
Not specified for diagnostic accuracy. For the engineering criteria (sterilization, biocompatibility, etc.), the ground truth is established by adherence to the respective international standards (e.g., ISO, IEC).
8. The sample size for the training set:
Not applicable/not specified. No information on an algorithm training set is provided; this is a medical device (probe) for measurement, not an AI/ML diagnostic algorithm.
9. How the ground truth for the training set was established:
Not applicable/not specified.
{0}------------------------------------------------
DEPARTMENT OF HEALTH & HUMAN SERVICES - USA
Public Health Service
Food and Drug Administration 10903 New Hampshire Avenue Document Control Center - WO66-G609 Silver Spring, MD 20993-0002
January 22, 2015
Deltex Medical Limited % Neil Armstrong RA Advisor To Deltex Medical Meddiquest Limited Quest Science, Orton Malborne Peterborough, PE2 5XS GB
Re: K142932
Trade/Device Name: Deltex Medical KDP72 Doppler Probe Regulation Number: 21 CFR 870.2120 Regulation Name: Extravascular Blood Flow Probe Regulatory Class: Class II Product Code: DPT Dated: October 10, 2014 Received: October 14, 2014
Dear Neil Armstrong,
We have reviewed your Section 510(k) premarket notification of intent to market the device referenced above and have determined the device is substantially equivalent (for the indications for use stated in the enclosure) to legally marketed predicate devices marketed in interstate commerce prior to May 28, 1976, the enactment date of the Medical Device Amendments, or to devices that have been reclassified in accordance with the provisions of the Federal Food, Drug, and Cosmetic Act (Act) that do not require approval of a premarket approval application (PMA). You may, therefore, market the device, subject to the general controls provisions of the Act. The general controls provisions of the Act include requirements for annual registration, listing of devices, good manufacturing practice, labeling, and prohibitions against misbranding and adulteration. Please note: CDRH does not evaluate information related to contract liability warranties. We remind you, however, that device labeling must be truthful and not misleading.
If your device is classified (see above) into either class II (Special Controls) or class III (PMA), it may be subject to additional controls. Existing major regulations affecting your device can be found in the Code of Federal Regulations, Title 21, Parts 800 to 898. In addition, FDA may publish further announcements concerning your device in the Federal Register.
Please be advised that FDA's issuance of a substantial equivalence determination does not mean that FDA has made a determination that your device complies with other requirements of the Act or any Federal statutes and regulations administered by other Federal agencies. You must comply
{1}------------------------------------------------
with all the Act's requirements, including, but not limited to: registration and listing (21 CFR Part 807); labeling (21 CFR Part 801); medical device reporting of medical devicerelated adverse events) (21 CFR 803); good manufacturing practice requirements as set forth in the quality systems (QS) regulation (21 CFR Part 820); and if applicable, the electronic product radiation control provisions (Sections 531-542 of the Act); 21 CFR 1000-1050.
If you desire specific advice for your device on our labeling regulation (21 CFR Part 801), please contact the Division of Industry and Consumer Education at its toll-free number (800) 638-2041 or (301) 796-7100 or at its Internet address
http://www.fda.gov/MedicalDevices/ResourcesforYou/Industry/default.htm. Also, please note the regulation entitled, "Misbranding by reference to premarket notification" (21 CFR Part 807.97). For questions regarding the reporting of adverse events under the MDR regulation (21 CFR Part 803), please go to
http://www.fda.gov/MedicalDevices/Safety/ReportaProblem/default.htm for the CDRH's Office of Surveillance and Biometrics/Division of Postmarket Surveillance.
You may obtain other general information on your responsibilities under the Act from the Division of Industry and Consumer Education at its toll-free number (800) 638-2041 or (301) 796-7100 or at its Internet address
http://www.fda.gov/MedicalDevices/ResourcesforYou/Industry/default.htm.
Sincerely yours,
Melissa A. Torres -S
Bram D. Zuckerman, M.D. For Director Division of Cardiovascular Devices Office of Device Evaluation Center for Devices and Radiological Health
Enclosure
{2}------------------------------------------------
DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration
Indications for Use
Form Approved: OMB No. 0910-0120 Expiration Date: January 31, 2017 See PRA Statement below.
510(k) Number (if known) Unknown - not yet assigned by FDA
Device Name KDP72, 72 Hour Doppler Probe
Indications for Use (Describe)
The probe is for use with the Deltex Medical CardioQ-EDM and CardioQ-EDM+ for Monitoring of cardiac output and fluid status. The probe is only approved for oral placement into the esophagus of a single anesthetized patient 15 years of age or younger, 50cm (20") to 170cm (67") in height.
Type of Use (Select one or both, as applicable)
Prescription Use (Part 21 CFR 801 Subpart D)
Over-The-Counter Use (21 CFR 801 Subpart C)
CONTINUE ON A SEPARATE PAGE IF NEEDED.
This section applies only to requirements of the Paperwork Reduction Act of 1995.
DO NOT SEND YOUR COMPLETED FORM TO THE PRA STAFF EMAIL ADDRESS BELOW.
The burden time for this collection of information is estimated to average 79 hours per response, including the time to review instructions, search existing data sources, gather and maintain the data needed and complete and review the collection of information. Send comments regarding this burden estimate or any other aspect of this information collection, including suggestions for reducing this burden, to:
Department of Health and Human Services Food and Drug Administration Office of Chief Information Officer Paperwork Reduction Act (PRA) Staff PRAStaff@fda.hhs.gov
"An agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a currently valid OMB number."
FORM FDA 3881 (8/14)
{3}------------------------------------------------
Contains Nonbinding Recommendations Appendix G
Appendix G: Example Diagnostic Ultrasound Indications For Use Format
CardioQ-EDM and CardioQ-EDM+ cardiac output and fluid status monitor System: KDP72 , 72 Hour Doppler Probe Transducer:
Intended Use: Diagnostic ultrasound imaging or fluid flow analysis of the human body as follows;
| Clinical Application | Mode of Operation | |||||||
|---|---|---|---|---|---|---|---|---|
| General(Track 1 Only) | Specific(Tracks 1 & 3) | B | M | PWD | CWD | ColorDoppler | Combined(Specify) | Other*(Specify) |
| Ophthalmic | Ophthalmic | |||||||
| FetalImaging& Other | Fetal | |||||||
| Abdominal | ||||||||
| Intra-operative (Specify) | ||||||||
| Intra-operative (Neuro) | ||||||||
| Laparoscopic | ||||||||
| Pediatric | ||||||||
| Small Organ (Specify) | ||||||||
| Neonatal Cephalic | ||||||||
| Adult Cephalic | ||||||||
| Trans-rectal | ||||||||
| Trans-vaginal | ||||||||
| Trans-urethral | ||||||||
| Trans-esoph. (non-Card.) | ||||||||
| Musculo-skeletal(Conventional) | ||||||||
| Musculo-skeletal(Superficial) | ||||||||
| Intravascular | ||||||||
| Other (Specify) | ||||||||
| Cardiac | Cardiac Adult | |||||||
| Cardiac Pediatric | ||||||||
| Intravascular (Cardiac) | ||||||||
| Trans-esoph. (Cardiac) | N | |||||||
| Intra-cardiac | ||||||||
| Other (Specify) | ||||||||
| PeripheralVessel | Peripheral vessel | |||||||
| Other (Specify) |
N = new indication; P = previously cleared by FDA; E = added under this appendix
- Examples of other modes of operation may include: A-mode, Amplitude Doppler, 3-D Imaging, Harmonic Imaging, Tissue Motion Doppler, and Color Velocity Imaging
{4}------------------------------------------------
Image /page/4/Picture/1 description: The image shows the logo for "Deltex medical". The word "Deltex" is in a large, bold, blue font. Below "Deltex" is the word "medical" in a smaller, light gray font. The logo is simple and clean, with a focus on the company name.
Deltex Medical Limited Terminus Road Chichester United Kingdom, PO19 8TX 011 44 1243 774837 Tel: Fax: 011 44 1243 532534
510(k) Summary
as required by 21 CFR 807.92(c)
Submitter and Owner:
This Premarket Notification, 510(k), is submitted by: Graham Lowe Marketing and Operations Director For and on behalf of the Owner: Deltex Medical Ltd Terminus Road Chichester West Sussex PO19 8TX United Kingdom Tel: 011 44 1243 523174 Fax: 011 44 1243 532534
Date
This Summary was prepared on September 22, 2014
Classification name:
Extravascular blood flow probe
The FDA has classified: "Extravascular blood flow probe" in 21 CFR 870.2120 as a Class II medical device with Product Code DPT
Common/Usual Name:
probe, blood-flow, extravascular
{5}------------------------------------------------
K142932 page 2 of 4
Proprietary Name:
Deltex Medical Ltd KDP72 Doppler Probe
Establishment Reqistration Number:
- The device will be manufactured by: Deltex Medical Ltd Terminus Road Chichester West Sussex PO19 8TX United Kingdom Establishment Registration Number 9680933
and sterilized by: Sterigenics UK, Ltd Cotes Park Estate Somercotes Derbyshire DE55 4NJ
Establishment Registration Number 3002807091
United Kingdom
Substantial Equivalence:
The Deltex Medical Ltd KDP72 Doppler Probe is substantially equivalent in design, use and materials to the:
Deltex Medical Ltd I2n Series Doppler Probe - K073593 Deltex Medical Ltd DP240 Doppler Probe - K052989 and the Sometic Dynemo 3000 - K972798, now Arrow Hemosonic probe
Like the Inn Series Probe is for use with the Deltex Medical CardioQ-EDM and CardioQ-EDM+ systems, K111542 and K132139 respectively.
The Deltex Medical Ltd KDP72 Pediatric Doppler Probe is designed to be a shorter version of the current legally marketed Dp240 product with more depth markings. It has an open-coil spring, as used on the 12 series products instead of the closed coil used on the Dp240, to increase flexibility.
The Sometic Dynemo 3000 K972798 has been superseded by the Arrow Hemosonic probe (still K972798) which is indicated for pediatric use for patients above 15kg. The Deltex Medical Ltd KDP72 will be shorter and more flexible enabling it to be indicated for patients above 3kg.
{6}------------------------------------------------
K142932 page 3 of 4
Description:
The Deltex Medical Ltd KDP72 Pediatric Doppler Probe is an oral extravascular blood flow probe designed to work with the CardioQ-EDM and CardioQ-EDM+ Systems (K111542 and K132139 respectively). It consists of a shaft, which is a spring reinforced silicone tube, with an electrical connector on the machine end and an ultrasonic transmitting and receiving tip on the patient end. The tip is fully covered and sealed to the shaft with a silicone rubber boot and by wires running through the shaft to the connector. Visual product identification is provided at the machine end and the device is provided single packed sterile for single patient use.
Standard ultrasonic diagnostic extravascular blood flow probes have been successfully used with pediatric patients; however the KDP72 has been specially designed for pediatric patients with a shorter length, more depth markings and an open coil spring to increase the flexibility.
Intended Use:
The probe is for use with Deltex Medical CardioQ-EDM and CardioQ-EDM+ for monitoring of cardiac output and fluid status. The probe is only approved for oral placement into the esophagus of a single anesthetized patient 15 years of age or younger.
Performance Data
The performance data recommended in "Information for Manufacturers Seeking Marketing Clearance of Diagnostic Ultrasound Systems and Transducers", issued on September 9, 2008, has been included.
Additionally a flexibility test has been conducted on the subject and predicate devices which demonstrates the comparative flexibility.
Conclusion
Based on the information above, Deltex Medical Ltd concludes that the Deltex Medical Ltd KDP72 Doppler Probe in substantially equivalent to:
- the Deltex Medical Ltd I2 Series and Dp240 Doppler Probes (K073593 and . K052989), and
- the Arrow International, Inc, Hemosonic 100 Esophageal Probe (K972798 . Sometic Dynemo 3000).
{7}------------------------------------------------
| Feature | Deltex Medical'KDP72' | Deltex Medical'I₂n-series' | Deltex Medical'DP240' | Arrow'Hemosonic 100 Esophageal Probe' |
|---|---|---|---|---|
| Subject Device | Predicate Device#1 | Predicate Device#2 | Predicate Device#3 | |
| FDA 510k number | This Submission | K073593 | K052989 | K972798 |
| product name | KDP72 | I₂n-series | DP240 Probe | TransesophagealProbe |
| common name | 72 Hour PediatricDoppler probe | I₂n-series Dopplerprobe | 240 Hour DopplerProbe | Trans-esophagealProbe & SterileJacket |
| product number | 9081-7002 | 9090 - 70159090 - 70169090 - 7017 | 9070- 7006 | HSP - 02150 &HSS-02150 |
| Device Description | ||||
| Sterilization | Sterilized inaccordance withISO11135-1(version ofstandard currentat time ofsubmission) | Sterilized inaccordance withISO11135-1(version ofstandard currentat time ofsubmission) | Sterilized inaccordance withISO11135-1(version ofstandard currentat time ofsubmission) | Unknown |
| Shelf Life | ISO11607-1(version ofstandard currentat time ofsubmission) | ISO11607-1(version ofstandard currentat time ofsubmission) | ISO11607-1(version ofstandard currentat time ofsubmission) | Unknown |
| Biocompatibility | Tested inaccordance withISO 10993-5, ISO10993-10, ISO10993-7 (versionof standardcurrent at time ofsubmission) | Tested inaccordance withISO 10993-5, ISO10993-10, ISO10993-7 (versionof standardcurrent at time ofsubmission) | Tested inaccordance withISO 10993-5, ISO10993-10, ISO10993-7 (versionof standardcurrent at time ofsubmission) | Unknown |
| EMC andElectrical Safety | IEC60601-1,IEC60601-1-2,IEC606001-2-37(version ofstandard currentat time ofsubmission) | IEC60601-1,IEC60601-1-2,IEC606001-2-37(version ofstandard currentat time ofsubmission) | IEC60601-1,IEC60601-1-2,IEC606001-2-37(version ofstandard currentat time ofsubmission) | Unknown |
| Packaging | ISO 11607-1, ISO11607-2 (versionof standardcurrent at time ofsubmission) | ISO 11607-1, ISO11607-2 (versionof standardcurrent at time ofsubmission) | ISO 11607-1, ISO11607-2 (versionof standardcurrent at time ofsubmission) | Unknown |
a
14
§ 870.2120 Extravascular blood flow probe.
(a)
Identification. An extravascular blood flow probe is an extravascular ultrasonic or electromagnetic probe used in conjunction with a blood flowmeter to measure blood flow in a chamber or vessel.(b)
Classification. Class II (performance standards).