Nitrile Powder Free Patient Examination Gloves, Blue Color is a non-sterile disposable device intended for medical purposes that is worn on the examiner's hand or finger to prevent contamination between patient and examiner.

Device Description

Nitrile films form a barrier to body fluids and bloodborne Pathogens. The nitrile rubber is water tight under normal conditions of use. It's tensile properties cause it to conform to the hand, allowing movements necessary for a medical procedure. Nitrile glove is known to create a barrier to bloodborne pathogens and body fluids. ASTM conforming tensile properties create a glove that is strong and flexible. The glove is manufactured in accordance with the requirements of ASTM D6319 and ASTM D5151 requirements.

AI/ML Overview

The provided text describes the acceptance criteria and performance data for the "Minghao Nitrile Powder Free Patient Examination Gloves, Blue Color." This is a medical device, and the information is presented in the context of a 510(k) premarket notification for demonstrating substantial equivalence to a predicate device.

Here's the breakdown of the requested information:

1. Table of acceptance criteria and reported device performance:

Characteristic	Standard / Acceptance Criteria	Reported Device Performance
Dimension	ASTM standard D 6319-10 (Length ≥ 230 mm min; Width: Small 70-90mm, Medium 85-105mm, Large 100-120mm, Xlarge 110-130mm; Thickness: Finger 0.05mm min, Palm 0.05mm min)	Meets ASTM standard D 6319-10 (Length ≥ 230 mm min for all sizes; Width as per standard; Thickness: Finger 0.05mm min, Palm 0.05mm min)
Physical Properties	ASTM standard D 6319-10 (Before aging/after aging: Elongation ≥ 500%, Tensile Strength ≥ 14 MPa)	Meets ASTM standard D 6319-10 (Before aging/after aging: Elongation ≥ 500%, Tensile Strength ≥ 14 MPa)
Freedom from Pinholes	21 CFR 800.20, ASTM D6319-10, ASTM D5151-06 (Reapproved 2011) (Inspection Level I, AQL 2.5)	Meets listed standards (Inspection Level I, AQL 2.5)
Powder Residual	ASTM standard D 6319-10 and D6124-06 (Reapproved 2011) (< 2mg/glove)	Meets listed standards (Reported values below 2mg of residual powder)
Biocompatibility - Primary Skin Irritation	ISO 10993-10: Third Edition 2010-08-01	Under the conditions of the study, the subject device is non-irritating
Biocompatibility - Dermal Sensitization	ISO 10993-10: Third Edition 2010-08-01	Under the conditions of the study, the subject device is not a sensitizer

2. Sample size used for the test set and the data provenance:

Sample Size for Test Set: The document does not explicitly state the specific sample sizes used for each test (e.g., number of gloves tested for dimensions, pinholes, etc.). It refers to meeting the requirements of the ASTM standards, which typically specify sample sizes for testing, but these are not enumerated in this summary.
Data Provenance: The data is reported by Minghao Medical Products Co., Ltd., which is based in China. The data appears to be retrospective in the sense that it describes tests already conducted to qualify the product against established standards.

3. Number of experts used to establish the ground truth for the test set and the qualifications of those experts:

This type of device (patient examination gloves) does not involve "experts" establishing a 'ground truth' in the way a diagnostic AI device would. The "ground truth" is established by adherence to recognized international and national standards (ASTM, ISO, 21 CFR). The testing is performed in laboratories according to the specified methodologies within those standards.
Therefore, the concept of a number of experts and their qualifications for ground truth in this context is not applicable.

4. Adjudication method (e.g. 2+1, 3+1, none) for the test set:

Again, for this type of medical device and the tests performed (physical, chemical, biocompatibility), the concept of an adjudication method among experts is not applicable. The results are quantitative measurements against defined thresholds or qualitative assessments (e.g., "non-irritating") based on established protocols.

5. If a multi-reader multi-case (MRMC) comparative effectiveness study was done, If so, what was the effect size of how much human readers improve with AI vs without AI assistance:

No, an MRMC comparative effectiveness study was not done. This type of study is relevant for diagnostic AI devices where human readers interpret medical images or data. Examination gloves are a physical barrier device, not an AI diagnostic tool.

6. If a standalone (i.e. algorithm only without human-in-the-loop performance) was done:

No, a standalone algorithm performance study was not done. This is not an AI device. The "device performance" refers to the physical and biological characteristics of the glove itself, not an algorithm's output.

7. The type of ground truth used (expert consensus, pathology, outcomes data, etc):

The "ground truth" for this device's performance is defined by the established specifications within the referenced ASTM and ISO standards and FDA regulations (e.g., 21 CFR 800.20). For example, for pinholes, the ground truth is "AQL 2.5" as defined by a specific test method. For physical properties, it's specific tensile strength and elongation values. For biocompatibility, it's the absence of irritation or sensitization as determined by standardized biological tests. This is a form of standard-based ground truth / laboratory test results.

8. The sample size for the training set:

Not applicable. This device is not an AI algorithm that requires a "training set." The manufacturing process for gloves is typically validated through process controls and quality assurance testing against specifications, not machine learning training.

9. How the ground truth for the training set was established:

Not applicable. As there is no training set, there is no ground truth established for one.

Summary

{0}------------------------------------------------

Image /page/0/Picture/1 description: The image shows the logo for the U.S. Department of Health & Human Services. The logo consists of a circular seal with the text "DEPARTMENT OF HEALTH & HUMAN SERVICES - USA" arranged around the perimeter. Inside the circle is a stylized image of three human profiles facing to the right, stacked on top of each other.

Food and Drug Administration 10903 New Hampshire Avenue Document Control Center - WO66-G609 Silver Spring, MD 20993-0002

March 17, 2016

Minghao Medical Products Co., Ltd. % Chu Xiaoan Official Correspondent Room 1606 Bldg. 1 Jianxiang Yuan No 209 Bei Si Huan Zhong Rd Haidian District Beijing, 100083 CHINA

Re: K152707

Trade/Device Name: Minghao Nitrile Powder Free Patient Examination Gloves, Blue Color Regulation Number: 21 CFR 880.6250 Regulation Name: Patient Examination Regulatory Class: I Product Code: LZA Dated: January 28, 2016 Received: February 1. 2016

Dear Chu Xiaoan:

We have reviewed your Section 510(k) premarket notification of intent to market the device referenced above and have determined the device is substantially equivalent (for the indications for use stated in the enclosure) to legally marketed predicate devices marketed in interstate commerce prior to May 28, 1976, the enactment date of the Medical Device Amendments, or to devices that have been reclassified in accordance with the provisions of the Federal Food. Drug. and Cosmetic Act (Act) that do not require approval of a premarket approval application (PMA). You may, therefore, market the device, subject to the general controls provisions of the Act. The general controls provisions of the Act include requirements for annual registration, listing of devices, good manufacturing practice, labeling, and prohibitions against misbranding and adulteration. Please note: CDRH does not evaluate information related to contract liability warranties. We remind you, however, that device labeling must be truthful and not misleading.

If your device is classified (see above) into either class II (Special Controls) or class III (PMA), it may be subject to additional controls. Existing major regulations affecting your device can be found in the Code of Federal Regulations, Title 21, Parts 800 to 898. In addition, FDA may publish further announcements concerning your device in the Federal Register.

Please be advised that FDA's issuance of a substantial equivalence determination does not mean that FDA has made a determination that your device complies with other requirements of the Act or any Federal statutes and regulations administered by other Federal agencies. You must comply with all the Act's requirements, including, but not limited to: registration and listing (21 CFR Part 807); labeling (21 CFR Part 801); medical device reporting (reporting of medical device

{1}------------------------------------------------

related adverse events) (21 CFR 803); good manufacturing practice requirements as set forth in the quality systems (QS) regulation (21 CFR Part 820); and if applicable, the electronic product radiation control provisions (Sections 531-542 of the Act); 21 CFR 1000-1050.

If you desire specific advice for your device on our labeling regulation (21 CFR Part 801), please contact the Division of Industry and Consumer Education at its toll-free number (800) 638-2041 or (301) 796-7100 or at its Internet address

http://www.fda.gov/MedicalDevices/ResourcesforYou/Industry/default.htm. Also, please note the regulation entitled, "Misbranding by reference to premarket notification" (21 CFR Part 807.97). For questions regarding the reporting of adverse events under the MDR regulation (21 CFR Part 803), please go to

http://www.fda.gov/MedicalDevices/Safety/ReportaProblem/default.htm for the CDRH's Office of Surveillance and Biometrics/Division of Postmarket Surveillance.

You may obtain other general information on your responsibilities under the Act from the Division of Industry and Consumer Education at its toll-free number (800) 638-2041 or (301) 796-7100 or at its Internet address

http://www.fda.gov/MedicalDevices/ResourcesforYou/Industry/default.htm.

Sincerely yours,

Teiashri Purohit-Sheth, M.D.

Tejashri Purohit-Sheth, M.D. Clinical Deputy Director DAGRID/ODE/CDRH FOR

Erin I. Keith, M.S. Division Director Division of Anesthesiology, General Hospital, Respiratory, Infection Control and Dental Devices Office of Device Evaluation Center for Devices and Radiological Health

Enclosure

{2}------------------------------------------------

Indications for Use

510(k) Number (if known) K152707

Device Name

Minghao Nitrile Powder Free Patient Examination Gloves, Blue Color

Indications for Use (Describe)

Type of Use (Select one or both, as applicable)
-------------------------------------------------	--

Prescription Use (Part 21 CFR 801 Subpart D)

|X | Over-The-Counter Use (21 CFR 801 Subpart C)

CONTINUE ON A SEPARATE PAGE IF NEEDED.

This section applies only to requirements of the Paperwork Reduction Act of 1995.

DO NOT SEND YOUR COMPLETED FORM TO THE PRA STAFF EMAIL ADDRESS BELOW.

The burden time for this collection of information is estimated to average 79 hours per response, including the time to review instructions, search existing data sources, gather and maintain the data needed and complete and review the collection of information. Send comments regarding this burden estimate or any other aspect of this information collection, including suggestions for reducing this burden, to:

Department of Health and Human Services Food and Drug Administration Office of Chief Information Officer Paperwork Reduction Act (PRA) Staff PRAStaff@fda.hhs.gov

"An agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a currently valid OMB number."

{3}------------------------------------------------

Section 6 510(k) Summary

510(K) Summary

"This summary of 510(k) safety and effectiveness information is being submitted in accordance with the requirements of SMDA 1990 and 21 CFR 807.92."

"The assigned 510(k) number is: ニ

Premarket Notification [510(k)] Summary

1.0 Submitter:

Submitter's name :	Minghao Medical Products Co.,Ltd.
Submitter's address :	West Industrial Park, Luannan County,Tangshan City, 063500 Hebei Province,China
Phone number :	(86)315-8230716
Fax number :	(86)315-8010500
Name of contact person:	Pang Cuiru

Date of preparation : 2016-03-01

2.0 Name of the Device

Device Name:	Nitrile Powder Free Patient ExaminationGloves, Blue Color
Proprietary/Trade name:	Minghao Nitrile Powder Free PatientExamination Gloves, Blue Color
Common Name:	Exam gloves
Classification Name:	Patient examination glove
Device Classification:	I
Regulation Number:	21 CFR 880.6250
Panel:	General Hospital (80)
Product Code:	LZA

3.0 Predicate device

Device Name:	Nitrile Powder Free Patient Examination Gloves,Blue Color
Company name:	Tangshan Zhonghong Pulin Plastic Co.,Ltd.
510(K) Number:	K120970

4.0 Device Description:

How the device functions: 4.1

Nitrile films form a barrier to body fluids and bloodborne Pathogens

4.2 Scientific concepts that form the basis for the device

The nitrile rubber is water tight under normal conditions of use. It's tensile properties cause it to conform to the hand, allowing movements necessary for a

{4}------------------------------------------------

medical procedure.

4.3 Physical and performance characteristics such as design, materials and physical properties:

Nitrile glove is known to create a barrier to bloodborne pathogens and body fluids. ASTM conforming tensile properties create a glove that is strong and flexible. The glove is manufactured in accordance with the requirements of ASTM D6319 and ASTM D5151 requirements.

5.0 Device Intended Use (Indication for use):

6.0 Summary of the Technological Characteristics of the Device:

The Nitrile Powder Free Patient Examination Gloves, Blue Color, non sterile are summarized with the following technological characteristics compared to ASTM or equivalent standard.

Characteristics	Standard	Device performance
Dimension	ASTM standard D 6319-10.	Meets
Physical Properties	ASTM standard D 6319-10.	Meets
Freedom frompinholes	21 CFR 800.20	Meets
Powder Residual	ASTM standard D 6319-10 andD6124-06(Reapproved 2011).	Meets<2mg/glove
Biocompatibility	Primary Skin Irritation in rabbitsISO 10993-10: Third Edition2010-08-01.	Under the conditions of thestudy, the subject device isnon-irritating
	Dermal sensitization in theguinea pig ISO 10993-10: ThirdEdition 2010-08-01.	Under the conditions of thestudy, the subject device isnot a sensitizer

7.0 Substantial Equivalent Based on Assessment of Non-Clinical Performance Data:

Nitrile Powder Free Patient Examination Gloves, Blue Color, meet requirements per ASTM D6319-10.per ASTM D6124-06(Reapproved 2011), per 21 CFR 800.20 and ISO 10993-10: Third Edition 2010-08-01.

The performance test data of the non clinical tests that support a determination of substantial equivalent is the same as mentioned immediately above.

{5}------------------------------------------------

8.0 Substantial Equivalent Based on Assessment of Clinical Performance Data:

Clinical data was not needed for this submission.

9.0 Substantial Equivalence Comparison:

Features & Description	Predicate Device	Subject Devic	Result of Comparison
Company	Tangshan Zhonghong PulinPlastic Co.,Ltd.	Minghao Medical ProductsCo.,Ltd.	--
510(K) Number	K120970	K152707
Device name	Nitrile Powder Free PatientExamination Gloves, BlueColor	Nitrile Powder Free PatientExamination Gloves, Blue Color	same
Product Code	LZA	LZA	same
Size	Small/ Medium/Large/X large	Small/ Medium/Large/X large	same
Intend for use	Nitrile Powder Free PatientExamination Gloves, BlueColor is a disposable deviceintended for medicalpurposes that is worn on theexaminer's hand or finger toprevent contaminationbetween patient andexaminer.	Nitrile Powder Free PatientExamination Gloves, Blue Colora disposable device intended fomedical purposes that is worn onthe examiner's hand or finger tprevent contamination betweenpatient and examiner.	Substantiallyequivalent
DeviceDescription andSpecifications	Meets ASTM D 6319-10	Meets ASTM D 6319-10	Substantiallyequivalent
Dimensions--Length	Meets ASTMD6319-10$≥230$ mm min	MeetsASTM D6319-10$≥230$ mm min for all sizes	Substantiallyequivalent
Dimensions-- Width	Small 70-90 mmMedium 85-105mmLarge 100-120mmXlarge 110-130 mmMeets ASTM D6319-10	Small 70-90 mmMedium 85-105 mmLarge 100-120 mmX large 110-130 mmMeets ASTM D6319-10	Substantiallyequivalent
Dimensions--Thickness	Finger 0.05mm min.Palm 0.05mm min.Meets ASTM D6319-10	Thickness (mm) min.Finger 0.05 mm min.Palm 0.05 mm min.Meets ASTM D6319-10	Substantiallyequivalent
PhysicalProperties	Meets ASTM D6319-10Before aging/after aging$Elongation≥500%$$Tensile Strength≥14$ MPa	Meets ASTMD D6319-10Before aging/after aging$Elongation≥500%$$Tensile Strength≥ 14$ MPa	Substantiallyequivalent
FreedomfromPinholes	Meets• 21 CFR 800.20• ASTM D6319-10• ASTM D 5151-06(Reapproved 2011)	Meets• 21 CFR 800.20• ASTM D6319-10• ASTM D5151-06(Reapproved 2011)	Substantiallyequivalent
		Inspection Level IAQL2.5
ResidualPowder	Meets ASTMD 6124-06(Reapproved 2011)below 2mg of residualpowder	Meets ASTMD 6124-06(Reapproved 2011)Results generated values below2mg of residual powder	Substantiallyequivalent
Materials usedto fabricate thedevices	Nitrile	Nitrile	Substantiallyequivalent
Dusting orDonningPowder: name	PU	Polyurethane	Substantiallyequivalent
Compareperformancedata supportingsubstantialequivalence	MeetsASTM D5151-06(Reapproved 2011)ASTM D6319-10ASTM D6124-06(Reapproved 2011)	MeetsASTM D5151-06(Reapproved 2011)ASTM D6319-10ASTM D6124-06(Reapproved 2011)	Substantiallyequivalent
Single PatientUse	Single Patient Use	Single Patient Use	Substantiallyequivalent
Biocompatibility	SKIN IRRITATIONDERMAL andSENSITIZATIONSTUDIES Meets ISO10993-10:2002/Amd.1:2006	SKIN IRRITATION DERMALand SENSITIZATION STUDIESMeets ISO 10993-10: ThirdEdition 2010-08-01.Under the conditions of the study,not an irritant and underconditions of the study, not asensitizer.	Substantiallyequivalent
Labeling for thelegally marketeddevice to whichsubstantialequivalence isclaimed.	-Powder Free-Patient Examination Glove-Single Use Only- Manufactured For:- Lot-Blue colorNon sterile	-Powder Free-Patient Examination Glove-Single Use Only- Manufactured For:- Lot-Blue colorNon sterile	Substantiallyequivalent

{6}------------------------------------------------

10.0 Substantial Equivalence Comparison:

It can be concluded that the Nitrile Powder Free Patient Examination Gloves, Blue Color meet the ASTM standard or equivalent standard and FDA requirements for waterleak test on pinhole AQL., meet labeling claims.

It can be concluded that the Nitrile Powder Free Patient Examination Gloves, Blue is as safe, as effective, and performs as well as the predicate device, Nitrile Color Powder Free Patient Examination Gloves, Blue Color, Tangshan Zhonghong Pulin Plastic Co., Ltd.. K120970.

Regulation Number and Section

§ 880.6250 Non-powdered patient examination glove.

(a)
Identification. A non-powdered patient examination glove is a disposable device intended for medical purposes that is worn on the examiner's hand or finger to prevent contamination between patient and examiner. A non-powdered patient examination glove does not incorporate powder for purposes other than manufacturing. The final finished glove includes only residual powder from manufacturing.(b)
Classification. Class I (general controls). The device, when it is a finger cot, is exempt from the premarket notification procedures in subpart E of part 807 of this chapter subject to the limitations in § 880.9.