Search Results
Found 1 results
510(k) Data Aggregation
(86 days)
The Oasis Humidifier is an accessory for Respironics CPAP and BiPAP systems to provide moisture to the patient circuit. The Oasis is the only humidifier with the acoustical design that enables effective operation of Respironics' Auto-CPAP mode. As such, it is the only humidifier that can be used with Respironics' Auto-CPAP products (i.e., Virtuoso Smart CPAP System (K953930) and Quartet Clinical System (K963761, currently under review)). The Oasis can also be used with standard CPAP devices from other manufacturers which have maximum operating pressures of 20 cm H2O, and do not have bi-level or automatic pressure titration capabilities. Performance of non-Respironics CPAP systems with the Oasis humidifier should be verified before use.
The Oasis Humidifier (Figure 12-1) consists of a top ("lid"), bottom ("reservoir"), gasket, and a 24" reusable flexible tube that connects the Oasis to the pressuregenerating unit (Respironics CPAP or BiPAP unit). The lid and reservoir are held together by four release latches. The latches are connected to the reservoir. The Oasis has an inlet port and an outlet port on its lid. The inlet port is on the top of the lid. The inlet port is where water is poured into the reservoir and where flexible tube connects the Oasis to the pressure-generating unit. The outlet port is on the front of the lid. (The six-foot patient circuit tubing is attached to the Oasis outlet port.) A J-shaped tube molded in the top of this lid is an acousticallytuned passage. This passage gives the Oasis the acoustical characteristics that enable effective operation of Respironics' Auto-CPAP mode. As such, it allows the Oasis to be used as an accessory for Respironics' Auto-CPAP devices. The inlet port's 26 mm outside diameter corresponds with the larger end of the 24" flexible tubing (26 mm inside diameter). The smaller end of the tubing -- 22 mm inside diameter -- connects to the outlet port of the pressure-generating unit. Refer to K945782 for complete information on the 24" flexible tubing. The Oasis (excluding the gasket) is made of dishwasher-safe plastic.
The provided document describes the Oasis Humidifier (K964653), which is a medical device accessory for CPAP and BiPAP systems. This submission is a Premarket Notification (510(k)), indicating that the company is demonstrating substantial equivalence to a predicate device, not necessarily a new clinical study to establish novel performance criteria.
Therefore, many of the requested criteria for a clinical study on device performance (such as sample size for test set, number of experts, adjudication methods, MRMC studies, standalone performance, training set details) are not applicable (N/A) in this context, as this is a submission demonstrating equivalence through verification and validation (V&V) engineering tests against established standards and predicate device performance, not a clinical effectiveness trial for a new AI/imaging device.
Here's the information based on the provided text:
1. Table of Acceptance Criteria and Reported Device Performance
Acceptance Criteria (Specification) | Reported Device Performance (Oasis Humidifier) |
---|---|
Ambient Operating Temperature: 5° to 40° C | Met (implied by "Testing was performed to demonstrate that the performance of the Oasis Humidifier in its intended environment is as safe and effective as that of the legally marketed predicate device.") |
Storage Temperature: -20° to +60° C | Met (implied) |
Ambient Operating Relative Humidity Range: 5% to 95% | Met (implied) |
Reservoir Capacity: 440 ml | 440 ml (2 cups) |
Relative Humidity Output: >25% (at 85 L/min flow, 3-20 cm H2O pressure, 5% RH at 40° C dry inspiratory air, distilled water) | Minimum of 25% RH |
Humidification Duration (full reservoir): Approximately 10 hours (at specified environmental conditions) | Approximately 10 hours |
Pressure Drop (humidifier and 24" tubing): 0.17 cm H2O (on-condensing at 30 L/min); 0.5 cm H2O (at 60 L/min) | 0.5 cm H2O @ 60 LPM (reported as negligible) |
Acoustic characteristics for Auto-CPAP mode: Acoustically-tuned passage | Has acoustically-tuned passage for effective operation with Respironics' Auto-CPAP devices |
Ability to operate with standard CPAP devices (non-Respironics, max 20 cm H2O, no bi-level/auto titration) | Can be used with compatible standard CPAP devices; tested with Respironics REMstar CPAP System (representative) |
Cleaning validation: Hand washing, Dishwasher cleaning (reservoir/lid only) | Validated |
Disinfection validation: Pasteurization | Validated |
Sterilization validation: Ethylene Oxide (EtO) Sterilization | Validated |
Bulk liquid not entering patient circuit when tilted up to 20° | By design, bulk liquid will not enter any other part of the patient circuit when device is tilted up to 20°. |
2. Sample Size Used for the Test Set and Data Provenance
- Sample Size for Test Set: Not applicable in the context of human data. The "test set" here refers to engineering verification and validation (V&V) testing performed on the Oasis Humidifier physical units. The document does not specify the number of units tested, but rather the performance parameters.
- Data Provenance: Not applicable as this relates to engineering and performance testing of the device itself, rather than human data. The testing was carried out by Respironics, Inc. in the United States. The data is prospective in the sense that the testing was performed specifically for this submission.
3. Number of Experts Used to Establish the Ground Truth for the Test Set and Qualifications of Those Experts
- Not Applicable. Ground truth, in the sense of expert review for diagnostic accuracy or clinical outcomes, is not established for this type of device submission. The "ground truth" for the engineering tests would be the established scientific and engineering principles, and the specifications of the predicate device and relevant standards. The testing itself is conducted by qualified engineers and technicians.
4. Adjudication Method for the Test Set
- Not Applicable. Adjudication methods (e.g., 2+1) are common in clinical studies where expert consensus on controversial findings is needed. This is an engineering V&V process, where test results are compared directly against predefined acceptance criteria from specifications or standards.
5. If a Multi-Reader Multi-Case (MRMC) Comparative Effectiveness Study was done, If so, what was the effect size of how much human readers improve with AI vs without AI assistance
- Not Applicable. This is a physical medical device (humidifier), not an AI-powered diagnostic or imaging device. Therefore, MRMC studies and AI assistance comparisons are irrelevant.
6. If a Standalone (i.e. algorithm only, without human-in-the-loop performance) was done
- Not Applicable. This is a physical medical device, not an algorithm, so "standalone" performance in the AI context does not apply. The device's performance characteristics (e.g., humidity output, pressure drop) are inherent to its design and functional operation without human intervention during its humidifying function.
7. The Type of Ground Truth Used
- Engineering Specifications and Standardized Test Methods: The "ground truth" is defined by the device's technical specifications (e.g., reservoir capacity, temperature ranges, humidity output targets), relevant medical device standards (implied by "certified to the standards referenced in the 'FDA Reviewer Guidance for Premarket Notifications'"), and the performance characteristics of the legally marketed predicate device (RI Humidifier, K945782). For example, for pressure drop, the "ground truth" is the scientifically measurable resistance to flow that determines if it's within acceptable limits and comparable to the predicate.
8. The Sample Size for the Training Set
- Not Applicable. This device does not involve a "training set" in the context of machine learning or AI.
9. How the Ground Truth for the Training Set was Established
- Not Applicable. As there is no "training set," there is no ground truth established for it.
Ask a specific question about this device
Page 1 of 1