(37 days)
A patient examination glove is a disposable device intended for medical purpose that is worn on the examiner's hand or finger to prevent contamination between patient and examiner.
Latex Patient Examination Gloves (Pre-powdered)
The provided text is related to a 510(k) premarket notification for "Latex Examination Gloves (Pre Powdered)" from USG HealthGuard Sdn. Bhd. It's an FDA clearance letter from 1999, not a study evaluating a medical device's performance against acceptance criteria. Therefore, the requested information (acceptance criteria, study details, sample sizes, expert qualifications, etc.) is not present in the provided document.
This document merely confirms that the FDA reviewed the 510(k) notification and determined the device (Latex Examination Gloves) is substantially equivalent to devices marketed before May 28, 1976. It does not contain any performance studies, acceptance criteria for device performance, or details on clinical trials or AI evaluation.
To answer your request, I would need a document describing a performance study of a device, including its acceptance criteria and results.
{0}------------------------------------------------
Image /page/0/Picture/1 description: The image is a black and white logo for the Department of Health & Human Services - USA. The logo consists of a circular border with the text "DEPARTMENT OF HEALTH & HUMAN SERVICES - USA" arranged around the perimeter. Inside the circle is a stylized image of three overlapping human profiles, with flowing lines extending from the bottom of the profiles.
Public Health Service
Food and Drug Administration 9200 Corporate Boulevard Rockville MD 20850
JUN 2 4 1999
Mr. Toh Chee Yeong General Manager USG HealthGuard Sdn. Bhd. (Company No. 183887-X) Lot 2756, Jalan Kempas Lama (Off 8 Miles, Jalan Skudai) 81300 Tampoi Johor Bahru, Johor MALAYSIA
Re: K991690 Latex Examination Gloves (Pre Powdered) Trade Name: Requlatory Class: I Product Code: LYY May 3, 1999 Dated: Received: May 18, 1999
Dear Mr. Toh Chee Yeong:
We have reviewed your Section 510(k) notification of intent to market the device referenced above and we have determined the device is substantially equivalent (for the indications for use stated in the enclosure) to devices marketed in interstate commerce prior to May 28, 1976, the enactment date of the Medical Device Amendments, or to devices that have been reclassified in accordance with the provisions of the Federal Food, Drug, and Cosmetic Act (Act). You may, therefore, market the device, subject to the general controls provisions of the Act. The general controls provisions of the Act include requirements for annual reqistration, listing of devices, good manufacturing practice, labeling, and prohibitions against misbranding and adulteration.
If your device is classified (see above) into either class II (Special Controls) or class III (Premarket Approval), it may be subject to such additional controls. Existing major regulations affecting your device can be found in the Code of Federal Regulations, Title 21, Parts 800 to 895. ਬੈ substantially equivalent determination assumes compliance with the Good Manufacturing Practice for Medical Devices: General (GMP) regulation (21 CFR Part 820) and that, through periodic GMP inspections, the Food and Drug Administration (FDA) will verify such assumptions. Failure to comply with the GMP requlation may result in regulatory action. In addition, FDA may publish further announcements concerning your device in the Federal Register.
{1}------------------------------------------------
Page 2 - Mr. Toh Chee Yeong
this response to your premarket notification Please note: submission does not affect any obligation you might have under sections 531 through 542 of the Act for devices under the Electronic Product Radiation Control provisions, or other Federal laws or regulations.
This letter will allow you to begin marketing your device as described in your 510(k) premarket notification. The FDA finding of substantial equivalence of your device to a legally marketed predicate device results in a classification for your device and thus, permits your device to proceed to the market.
If you desire specific advice for your device on our labeling requlation (21 CFR Part 801 and additionally 809.10 for in vitro diagnostic devices), please contact the Office of Compliance at (301) 594-4692. Additionally, for questions on the promotion and advertising of your device, please contact the Office of Compliance at (301) 594-4639. Also, please note the regulation entitled, "Misbranding by reference to premarket notification" (21 CFR 807.97). Other general information on your responsibilities under the Act may be obtained from the Division of Small Manufacturers Assistance at its toll-free number (800) 638-2041 or (301) 443-6597 or at its internet address
"http://www.fda.gov/cdrh/dsmamain.html".
Sincerely yours,
Timothy A. Ulatowski
Timd W A. Director Division of Dental, Infection Control, and General Hospital Devices Office of Device Evaluation Center for Devices and Radiological Health
Enclosure
{2}------------------------------------------------
Indications For Use Statement.
| 510 (K) Number (if known) | K99 1690 |
|---|---|
| Device Name | Latex Patient Examination Gloves (Pre-powdered) |
: A patient examination glove is a disposable Indication For Use device intended for medical purpose that is worn on the examiner's hand or finger to prevent contamination between patient and examiner.
(PLEASE DO NOT WRITE BELOW THIS LINE-CONTINUE ON ANOTHER PAGE IF NEEDED)
Concurrence of CDRH, Office of Device Evaluation (ODE)
Olin S. h'n
ion St Division of De and General He 510(k) Number
Prescription Use (Per 21 CFR 801.109) OR Over-The-Counter Use _
(Optional Format 1-2-96)
§ 880.6250 Non-powdered patient examination glove.
(a)
Identification. A non-powdered patient examination glove is a disposable device intended for medical purposes that is worn on the examiner's hand or finger to prevent contamination between patient and examiner. A non-powdered patient examination glove does not incorporate powder for purposes other than manufacturing. The final finished glove includes only residual powder from manufacturing.(b)
Classification. Class I (general controls). The device, when it is a finger cot, is exempt from the premarket notification procedures in subpart E of part 807 of this chapter subject to the limitations in § 880.9.